Clean installation of faucets, sinks, toilets, showerheads, tub spouts, and bidets — with new supply lines and shut-off stops, correct seals, and a leak test before we leave. Old fixture hauled away.
Fixture Installation is one part of our plumbing repair coverage in Arizona. For the full picture — symptoms, costs, and when to repair vs. replace — start with the complete Plumbing Repair guide, or browse every plumbing repair service we offer.
A fixture install looks simple until a corroded shut-off won't close, the old supply lines crumble, or a big-box faucet arrives with the wrong connections for your rough-in. Doing it right means replacing the shut-off stops and supply lines while everything is open, seating the fixture on a fresh seal, setting it level and secure, and running water to confirm no drips at any connection before the cabinet or wall closes. We install faucets, sinks, toilets, showerheads, tub spouts, and bidets so the finished job looks clean and stays dry.
We bring the parts that turn a fixture swap into a one-trip job — new quarter-turn angle stops to replace seized multi-turn valves, braided stainless supply lines instead of the old rubber ones, fresh wax rings or waxless seals for toilets, and plumber's putty or silicone for sink and drain seats. On a faucet we check the aerator and flow, on a toilet we confirm the flush and the seal at the floor, and on a shower fixture we verify the valve and diverter. The old fixture goes with us and gets recycled.
Fixture installs are where an efficiency or accessibility upgrade pays off — a WaterSense faucet or a 1.28-gallon toilet cuts the Arizona water bill, a pressure-balanced shower valve stops the scald when someone flushes, and a comfort-height toilet or a hand-held shower makes a bathroom easier to use. We size and confirm the fixture against your rough-in before the visit so odd hole spacing, older supply threads, or a tight vanity across Arizona don't turn a same-day install into a callback.
A faucet green with corrosion or a toilet weeping at the floor is past sealing and due for replacement. Installing a new one is the cleaner economic call than chasing seals on a worn Arizona fixture.
Remodeling or updating a room
New fixtures are the fastest visible upgrade in a kitchen or bath. We set them to code with fresh shut-offs and supply lines so the new look isn't hiding old failure points.
Upgrading to low-flow or efficient models
A WaterSense faucet, aerator, or 1.28-gallon toilet cuts water use noticeably in a Arizona home. Correct installation is what makes the rated savings real.
Adding a fixture that wasn't there
A prep sink, a bidet, or a second-vanity faucet needs a new supply tap and sometimes a drain tie-in. We run it to code so the addition is permanent, not a patch.
Accessibility needs have changed
Comfort-height toilets, lever faucets, and hand-held showers make a bathroom usable for aging or mobility needs. Swapping the fixture is a small job with a large daily payoff across Arizona.
Common causes & what we fix
Fixture at end of service life
Cartridges, seals, and finishes wear out, and a fixture that's been repaired repeatedly is cheaper to replace. It's the most common reason a Arizona homeowner books an install.
Remodel or design change
A new vanity, counter, or tile job usually means new fixtures to match. We coordinate the install around the finish work so nothing gets scratched or leaks behind it.
Water-efficiency upgrade
Older faucets and toilets use two to three times the water of current models. Replacing them is a direct cut to the Arizona water bill and a common upgrade trigger.
Damaged or cracked fixture
A cracked sink, a chipped toilet, or a snapped handle isn't worth repairing. Replacement restores function and rules out a slow leak from the damage across Arizona.
Failed builder-grade hardware
Builder-grade faucets and fill valves fail early, and swapping to a quality fixture ends the cycle. It's a frequent upgrade in newer Arizona homes a few years in.
What to expect, start to finish
1
Call or schedule online. Book your fixture installation in Arizona online or by phone and pick a 2-hour window. We confirm in under five minutes with the assigned tech's name and photo.
2
We diagnose on-site. Diagnosis happens on-site: free for most fixture installation repairs, $39 on minor service calls (waived if you proceed). Nothing starts until you've seen the issue and the plan.
3
Flat-rate quote. You get a flat-rate fixture installation quote in writing, good for 30 days — no hourly creep and no add-ons after the fact.
4
Same-visit fix. Because the trucks carry the common valves, fittings, cartridges, and fixtures, most fixture installation jobs wrap in that same visit — second trips are rare.
The real cost of fixture installation in Arizona
Fixture Installation in Arizona starts at from $129, every fixture installation quote is flat-rate and presented in writing before work begins — no surprise add-ons, no hourly creep. Seniors (65+) and military save 10% on labor, and financing covers projects over $1,500 at 0% APR for 12 months, with no prepayment penalty.
Why trust us with fixture installation in Arizona
We've been a trusted choice since 1974 — over 50 years of family-owned plumbing service across Arizona. Our techs are CSLB-licensed (#1098234), background-checked, and complete an internal 12-week training program before rolling on calls alone.
Our fixture installation carries a 10-year workmanship guarantee — separate from any manufacturer warranty on the parts themselves. If the fixture installation we performed fails because of how we did it, we come back and fix it free for a full decade. Appliances and fixtures we install are backed by their full manufacturer warranty, and the parts and accessories we fit carry standard 1–5 year warranties by item.
We quote fixture installation on honest scope: no unnecessary up-sell, salaried (never commissioned) technicians, and a transparent diagnostic so you see exactly what we see — including the parts still in good shape. If a repair is the right call we say so; if replacement is the better long-term economics, we say that. The flat-rate fixture installation quote is written and good for 30 days.
Where to get fixture installation from us
We provide fixture installation throughout Arizona, with fast coverage in every major Arizona metro.
Reach times for fixture installation vary by traffic and time of day, so we quote an accurate ETA when you call — and the dispatch line routes straight to an on-call technician, no voicemail in between.
Fixture Installation questions, answered
Top questions homeowners searching for Fixture Installation near me ask us:
Is the old fixture removed?
Yes — the old faucet, sink, toilet, or shower hardware is removed and recycled through metal and fixture channels. We don't leave the old unit behind after an Arizona job.
Do you supply the fixture or do I?
Either works. Many Arizona homeowners buy the fixture they like and we install it; we can also supply quality Kohler, Moen, or Delta models. If you buy it yourself, send us the model so we confirm it fits your rough-in before the visit.
Can you install a fixture with an odd rough-in?
Yes — nonstandard hole spacing, older supply threads, and tight cabinets are routine. We measure and confirm parts before coming to your Arizona home, including ZIPs , so it stays a one-trip install.
Will you replace the shut-off valves too?
We recommend it and usually do — the old multi-turn stops seize and weep, and replacing them with quarter-turn valves while everything is open costs little and prevents the next leak. It's standard on our Arizona installs.
How long does a fixture installation take?
A standard faucet, toilet, or showerhead swap runs 1–2 hours including new shut-offs, supply lines, and a leak test. Adding a fixture that needs a new supply or drain line takes longer across Arizona.